DuraVent B-Vent Gas Pipe - Model BV

From$59.52

DuraVent B-Vent Gas Chimney Pipe is used to vent natural gas and propane appliances such as natural gas fireplaces, gas-fired furnaces, boilers, water heaters, and wall or space heating applications. UL is listed to meet UL 441 and CAN/ULC-S605 standards for 1" clearance to combustible material. Constructed with an aluminum... Read More

From$81.03

DuraVent B-Vent Adjustable Elbows are used to offset the vent pipe to avoid any obstructions while maintaining the proper 1" clearance to combustibles. Available in either 45/60 degree and 90 degree angles. The 45/60 degree is able to adjust to any angle between straight up and down to a 45... Read More

From$38.77

DuraVent B-Vent Adjustable Length Pipe is used to get the perfect length of pipe when the vent path calls for a specific length of pipe. B-Vent pipe is unable to be cut to length which makes the adjustable pipe a great solution. The adjustable length pipes work by telescoping up... Read More

From$111.12

DuraVent B-Vent Tee Connection With Removable Clean Out Cap is used for connecting more than one appliance to the Dura-Vent B-vent pipe. It is very common to connect the exhaust of a furnace or boiler and a hot water heater. The tee connection allows the two pipes together to reach... Read More

From$48.97

DuraVent B-Vent Universal Adapters are used to connect DuraVent Type B-vent pipe to either another manufacturer's type B-Vent or a flexible chimney liner. Use the male adapter when converting another manufacturer's B-vent to the DuraVent B-Vent when the DuraVent will be on the top side of the vent pipe. Use... Read More

From$32.16

DuraVent B-Vent Draft Hood Connector is used to connect the DuraVent B-Vent to either a single wall connector pipe or directly to the appliance. The connection end is female to slide over the connector pipe of the appliance exhaust collar. Use sheet metal screws to attach the single wall end... Read More

From$31.28

DuraVent B-Vent Adjustable Flashing is used to waterproof seal around the pipe to waterproof the roof penetration. The flashing is available in 0/12 thru 6/12 pitch for low slope roofs and also 7/12 thru 12/12 for steeper roofs. The flashing is used for shingle roofs only. The flashing will tuck... Read More

From$7.88

DuraVent B-Vent Storm Collar is used to seal around the DuraVent B-vent pipe as it passes through either a roof flashing or a chimney chase cover. Silicone will need to be applied to make a seal around the storm collar where it meets the pipe above the cover or flashing.... Read More

From$68.19

DuraVent B-Vent High Wind Rain Cap is used to terminate the pipe at the top of the vent. The High Wind cap prevents rain from entering the chimney pipe while also preventing any wind related downdrafts. The rain cap easily twist on and off for inspections and maintenance. Used for... Read More

From$20.73

DuraVent B-Vent Firestop Trim Spacer is used at every level of the home the DuraVent B-vent pipe passes through. The Firestop Spacer also acts as a trim collar for the first level of the home.

From$115.52

DuraVent B-Vent Wall Support is used for vertical and horizontal support of the DuraVent B-vent pipe. The wall supports should be used every 4' of vent pipe. The wall support legs can be rotated 360 degrees for wherever you need to place the support on a wall or a ceiling. Read More

From$53.89

DuraVent B-Vent Wall Thimble is used to pass the DuraVent B-vent pipe through a combustible wall. The Wall Thimble provides the necessary 1" clearance from any combustible materials. The Wall Thimble is able to adjust from 3.5" to 6" to accommodate various wall thicknesses. The integrated trim collar provides a... Read More

From$64.61

DuraVent B-Vent Increasers are used to increase the DuraVent B-Vent pipe. This is typically done when connecting two vent pipes together such as a hot water heater and a furnace which have different vent sizes. The small end of the increaser will be pointed down and the large side of... Read More