Selkirk Metalbestos Ultra-Temp Class A Chimney Pipe

From$145.99

Stainless Steel Inner and Outer Chimney Pipe The Metalbestos Chimney System (MCS) is ideal for venting residential heating appliances burning wood, #2 oil, and natural and LP gas. They have been specifically designed for today's modern, high-efficiency “airtight” wood stoves. They are designed for gravity (natural draft), non-positive internal pressure... Read More

From$827.99

Ideal for to use with natural draft home heating systems that burn wood, natural gas, lp gas, and #2 oil. It has been specifically designed for today's modern high efficiency wood stoves, wood burning heaters, and for combination fuels in central heating systems. UL103 Standard for safety factory-built chimneys for... Read More

From$670.99

Ideal for to use with natural draft home heating systems that burn wood, natural gas, lp gas, and #2 oil. It has been specifically designed for today's modern high efficiency wood stoves, wood burning heaters, and for combination fuels in central heating systems. UL103 Standard for safety factory-built chimneys for... Read More

From$1,331.99

Ideal for to use with natural draft home heating systems that burn wood, natural gas, LP gas, and #2 oil. It has been specifically designed for today's modern high efficiency wood stoves, wood burning heaters, and for combination fuels in central heating systems. UL103 Standard for safety factory-built chimneys for... Read More

From$81.99

The Chimney Pipe Adapter is used to connect Selkirk Class A chimney pipe to either Double Wall or Single Wall Stove Pipe. The Pipe Adapter is used for new installations since it needs to attach to the bottom of the Selkirk Class A pipe. If you are using Rock-Vent Double... Read More

From$169.99

The Round Top Chimney Cap is designed with a dome to exclude rain and leaves, and a lower skirt to deflect wind for proper chimney draft. Fabricated from 430 stainless steel. In the 5", 6", 7", and 8" sizes, the Round Top is designed with three legs that slide down... Read More

From$28.99

The Selkirk Class A Storm Collar is designed to fit on Selkirk Class A round chimney pipe just above the roof flashing. The upper edge of the Storm Collar should be waterproofed with silicone sealer to prevent any water from leaking between the Storm Collar and chimney pipe. Fabricated from... Read More

From$240.99

Flashings are used to seal the opening where the chimney penetrates the roof to divert rain and snow down from the roof and away from the chimney system. Chimney silicone sealant will come in handy with this installation. Selkirk flashing is fabricated from aluminum. A series of adjustable flashings are... Read More

$373.99

Our UL-listed kit allows rubber flashings to be safely used for Selkirk chimney pipe installations on metal corrugated roofs with pitches up to 12/12. This kit includes a special storm collar, engineered for this kit for maximum weather protection. The kit also includes: rubber boot, spacer kit and boot mounting... Read More

$186.99

The Selkirk Roof Brace Kit can be used whenever there is a need to stabilize the chimney above the roof level. The Roof Brace Kit should be used at a midpoint on the chimney. Braces adjust from 4' to 6'. Fits Selkirk Ultra Temp Class A Pipe I.D. diameters 5"... Read More

From$28.99

All Selkirk Metalbestos insulated pipe lengths are furnished with a Locking Band, for extra security when assembling your pipe. Locking Bands come pre-assembled, with captured nut and screw. Selkirk UT Chimney Pipe & Components Guide Measurement Chart: Selkirk Class A Pipe Locking Band Size 6" 7" 8" A 8" 9"... Read More

From$71.99

The Selkirk Wall Band is used along a wall to provide a 2" clearance and stability. It is also useful for suspending offsets, and required at 8' or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall. Selkirk UT Chimney Pipe & Components Guide Measurement... Read More

From$143.99

Our Selkirk Insulated Wall Thimble installs quickly and eliminates the need for using individual firestops. Interior plate has black matte finish. The round shielding acts as a radiation shield and provides the required 2" airspace clearance to combustibles. The two sections telescope to accommodate 6" to 11" wall thickness. Selkirk... Read More

$177.99

This new design gives you the flexibility of securing the 6", 7" or 8" diameter chimney with a heavy duty band. The Selkirk Roof Support band allows you to slide the installed length vertically to properly position this section in the system. Installation requirements are the same as our standard... Read More

From$313.99

This is an ideal support assembly for freestanding fireplaces and open cathedral ceiling installations. Fits all roof pitches and requires only simple framing. The Selkirk Roof Support mounts easily on to top of roof through opening that allows 2" clearance. Maximum length of chimney which can be suspended below is... Read More

From$500.99

The 15° Insulated Elbows can be used for fixed offsets of 15° slope or in pairs for offsets adjustable from 0° to 30° slope. The 30° Insulated Elbow can be used for fixed offsets of 30° slope. Greater angles are prohibited by ULR Standard. Now includes 2 Elbows, 2 Locking... Read More

From$472.99

The Insulated Chimney Tee may be used to start chimneys indoors or outdoors using a Wall Support Assembly. A length of Insulated Chimney Pipe is attached to the Tee snout to pass safely through combustible walls. An Insulated Tee Cap is included which can be removed from bottom opening for... Read More

From$147.99

Designed for new installations, the Dripless Stove Pipe Adapter with Coupler can be installed by twist-locking the Coupler on the DSAC into the first section of Selkirk Class A chimney pipe, and connects to Single Wall Stove Pipe. Length of adapter is 15". The end of the adapter may need... Read More

From$111.99

Dripless Stove Pipe Adapters are used to connect single wall stove pipe to Selkirk Class A chimney systems. They are designed to slip inside single wall stove pipe to contain any creosote dripping down the chimney to inside the stove pipe. The end of the adapter may need to be... Read More

From$79.99

The Pitched Ceiling Plate provides a finished appearance where the chimney passes through a sloped ceiling. Fits 2/12 to 6/12 or 6/12 to 12/12 range pitch for your installation. Selkirk UT Chimney Pipe & Components Guide  Measurement Chart: Selkirk Class A Pitched Ceiling Plate 2/12 - 6/12 Pitch Size 6"... Read More

From$216.99

The Finish Support Package includes a square trim plate. With proper framing, ceiling supports assure at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. The Round Finish Support Package is available in limited quantities. Please see dropdown menu... Read More

From$35.99

The Selkirk Finishing Collar fits over the lower end of a suspended insulated chimney pipe to provide a finished appearance, or is used to attach a Stove Pipe Adapter to the lower end of a chimney or to an Insulated Tee. Selkirk UT Chimney Pipe & Components Guide Measurement Chart:... Read More

From$178.99

The Wall Support is intended for use with the Insulated Tee as an interior or exterior support where the chimney has a lateral connection. It is also useful where the pipe connection passes through a combustible interior or exterior wall. Braces may be fastened to the wall either above or... Read More

From$117.99

The Anchor Plate provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. The Anchor Plate connects to the pipe with a twist-lock connection. Selkirk UT Chimney Pipe & Components... Read More

From$144.99

The Attic Shield is required where a chimney passes into an unoccupied attic space. Designed to keep blown-in or blanket insulation away from the chimney, and to maintain the mandatory 2 inch clearance to combustibles. Selkirk UT Chimney Pipe & Components Guide Measurement Chart Selkirk Attic Insulation Shield Size 6"... Read More

From$57.99

The Selkirk Firestop Joist Shield is used in floor / ceiling penetrations other than those which include a ceiling support. Not required when passing through roof. Selkirk UT Chimney Pipe & Components Guide Measurement Chart Selkirk Firestop Joist Shield Size 6" 7" 8" A 14" 15" 16" B 10" 11"... Read More

From$77.99

The Trimplate Spacer is used with Selkirk Class A chimney pipe when installing a Fire Stop or Roof Support Package in a flat ceiling. Selkirk UT Chimney Pipe & Components Guide Measurement Chart Selkirk Class A Trimplate Spacer Size 6" 7" 8" A 19" 21" 22" B 12" 13" 14"... Read More

$187.99

The Selkirk Universal Wall Support / Re-Support Assembly is designed to support a vertical wall installation above the tee or above an offset. It can also serve as an intermediate support. This universal design will work on 6, 7, and 8” diameters. Selkirk UT Chimney Pipe & Components Guide Vertical... Read More

$154.99

The Selkirk Interior Re-Support assembly allows for two different methods of chimney re-support. The first method is used at the immediate section of chimney above the upper elbow of an offset. With the appropriate Fire Stop Joist Shield in place, clamp the support band around chimney and attach with 6... Read More